How to change filters in Barnstead E-Pure , Nanopure and Nanopure II Water System

i-d-=-1-3-9-&-t-i-t-l-e-=-H-o-w-_-t-o-_-c-h-a-n-g-e-_-f-i-l-t-e-r-s-_-i-n-_-B-a-r-n-s-t-e-a-d-_-E---P-u-r-e-_-,-_-N-a-n-o-p-u-r-e-_-a-n-d-_-_-N-a-n-o-p-u-r-e-_-I-I-_-W-a-t-e-r-_-S-y-s-t-e-m- How to change filters in Barnstead E-Pure , Nanopure and Nanopure II Water System

APSWATER
High Quality, Low Prices, Honest Advice

800-460-9011
Toll Free

Main Menu
Home | Products | Tech Info | About US |

Purchase Orders Welcome
Call for quick pre-approval

Simply The Best

Stainless Steel
Water Distillers

Best
Safest
Purerst
Low Cost
Many Sizes

Treat Yourself

Reverse Osmosis
Clean and Safe
Inexpensive
Drinking Water

Improves Taste

Activated Carbon

Removes Chlorine Improves Taste

Low Maintenance

Chemical Free

Terminator Systems
Sulfur
Iron
Turbidity
Adjusts pH
Low Maintenance
1-30 G.P.M.

APS WATER DIVISIONS
Laboratory Water Residential/Commercial Water Syringe Filters

How to change filters in Barnstead E-Pure , Nanopure and Nanopure II Water System

New : Specialty Filters for Perchlorate, Chlorine, Nitrite, Metals, precious metals, uranium and many others

APS TechNotes See all articles

Although this proceedure is designed specifically for the Barnstead E-Pure Water Systems, it can also be used with the Barnstead Nanopure II and Nanopure Bioresearch (Quad) Systems.



SOP FOR FILTER CHANGE OF E-PURE WATER FILTRATION SYSTEM

1.PURPOSE: To instruct individuals in the proper replacement of filters for the Water Filtration System.

2.SCOPE: This document will allow individuals to change filters in the Water Filtration System to maintain system performance.

3. omited

4. DEFINITIONS:

4.1 E-Pure: Brand name of the water filtration system.

4.2 Filter/Cartridges: Interchangeable term for purification materials.

4.3 Canister: plastic housing for filter cartridge

4.4 Draw-off Valve: a valve found directly above filter 6

4.5 Locking pins:  a securing device for canisters 2-5

5. MATERIALS & EQUIPMENT:

5.1.    Replacement filters:

For systems being fed water contains high particulates

5.1.2 Replacment Filters  E-Pure replacement filters

5.1.2.a. Filter #1: D01801-MACROpure

5.1.2.b. Filter #2: SB1801-High Capacity

5.1.2.c. Filter #3: MB1801--ULTRApure DI SG

5.1.2.d. Filter #4: OS1801--ORGANICfree

5.1.3 Filter #5: FF0501- 0.2 micron final filter


You can also order kit B-MSMO2 which includes all the the above.

For systems being fed with clean Distilled or Reverse Osmosis water

5.1.2 E-PureReplacement filters

5.1.2.a. Filter #1: CF1801Cabon Filter

5.1.2.b. Filter #2: MB1801Mixed Bed Deionizer

5.1.2.c. Filter #3: MB1801Mixed Bed Deionizer

5.1.2.d. Filter #4: OS1801Organic Scavenger

5.1.3 Filter #5: FF0501 0.2 micron final filter


These can be order as a kit # B-CDDO2

5.2 Filter wrench

5.3 Water catch basin

6. PRECAUTIONS:

6.1 Ensure that locking pin is in fully locked position before pressurizing.

E-Pure or canister may release when system is pressurized.

6.2 Pretreatment cartridge (D0835 or D0836) must be rinsed in system by itself to avoid plugging of other purification cartridges.

6.3 Remove 0.2-micron hollow fiber filter from remote dispenser during installation and rinsing to avoid fouling or plugging a filter.

6.4  Always shut off the water to the E-pure and depressurize the system prior to removing canisters or filters.

6.5  To avoid the possibility of contaminating the outer surface of the cartridge during installation, use the following procedure when installing new cartridges.

6.5.1 Remove the new cartridge from its shipping box. Do not remove the plastic bag around the cartridge.

6.5.2 Stand the cartridge up on a bench, nipple end up.

6.5.3 Open the top end (nipple end) of the plastic bag.   Pull down the bag to expose the top third of the cartridge.

6.5.4 Taking care not to touch the exposed surface of the cartridge, install the cartridge (with the bag still around the lower portion) onto the head of the E-Pure.

6.5.5 When the head is securely holding the cartridge, pull the plastic bag off the cartridge.

6.5.6 Install O-Ring on top of canister.

6.5.7 Install the canister over the cartridge and secure with locking pin.

6.6   D3750, 0.2 micron final filter should be changed every 30 days to maximize system performance.

6.7  10 liters of water should be rinsed through a new filter prior to use.

7. PROCEDURE

7.1 Turn E-pure system off and unplug from power source.

7.2 Turn off water supply to E-pure system

7.2.1  Close the 2 valves in cupboard under E-pure system

7.2.1.1  Valve #1 is on top of filter #1

7.2.1.2  Valve #2 is a red valve to the right of valve #1 and controls the main water supply.

7.3  Depressurize the E-pure system.

7.3.1  Refer to Diagram # 1 and precaution 6.3

7.3.2  Close drawoff valve by turning to a horizontal position.

7.3.3  Remove and discard filter/cartridge #6.

7.3.4 Reverse drawoff tubing draining into the sink.

7.3.5 Open drawoff valve (vertical position) and let the system depressurize until no more liquid is draining.

7.4  Remove and replace filter/cartridge #1

7.4.1   Place water catch basin under filter

7.4.2 Use filter wrench to grip canister and turn _ turn to the left and remove.

7.4.3 Discard filter/cartridge.

7.4.4 Wash canister with soap and water and rinse until no soap residue is visible.

7.4.5 Install new 50mm prefilter.

7.4.6 Reinstall canister with new filter/cartridge in position #1

7.5 Remove and replace filter/cartridge #2

7.5.1 See Diagram #1 for location.

7.5.2 Place water catch basin under filter.

7.5.3 Disengage locking pin on canister ring and turn _ turn to the left to remove canister.

7.5.4 Using filter wrench if needed, turn filter/cartridge _ turn to left and remove.

7.5.5 Discard filter/cartridge.

7.5.6 Wash canister #2 with soap and water and rinse until no soap residue is visible.

7.5.7 Install filter #2. See PRECAUTION #6.5.

7.6   Remove filter/cartridges  #3 - #5

7.6.1 See Diagram #1 for location of filters

7.6.2 Place water catch basin under filter being removed.

7.6.3 Remove canisters and discard filters/cartridges.

7.6.4 Wash canisters with soap and water and rinse until soap residue is not visible,

7.6.5 Reinstall canisters 3-5  WITHOUT cartridges.

7. 7  Rinse system and filter # 2. SEE PRECAUTION # 6.2.

7.7.1 Turn on water supply

7.7.2 Plug in power supply to E-pure and turn power ON.

7.7.3 Allow water to run from drawoff tubing into sink for 10-20 min.

7.7.3.1 This removes any preservation resin from the system that came from the newly installed filter/cartridge #2.

7.7.4 Turn power and water supply to E-pure OFF.

7.8 Replace filter/cartridges #3- #5.

7.8.1   Place water catch basin under canister being removed.

7.8.2 Remove canisters 3-5 and rinse again with water.

7.8.3 Install new filters/cartridges and O-rings

7.8.3.1 Refer to materials list for proper filter/cartridge and O-rings.

7.8.3.2 Refer to PRECAUTION # 6.5 for proper installation of filter/cartridges

7.8.3.3 See PRECAUTION #1

7.9  Turn water supply to E-pure ON.

7.10  Plug in power supply and turn E-pure power supply ON.

7.11  Allow water to drain into sink for 10-20 min.

7.12  Close petcock valve on drawoff tubing.

7.13  Replace filter/cartridge #6

7.13.1 See Materials list for proper filter.

7.14  Replace drawoff hose in original position.

7.15  Open petcock valve and allow water to drain for 10-15 min. through final filter.

Got questions?

I am here to help

Just Ask Amy.
Click Here!

Are You Lost?
See Your Breadcrumbs

Free Shipping*

UPS Freight
Included in price.

Click for coupon
of the day

Got Lab filters?
Try the new
LabFilter.com

Got Lab Water?
Go To
LabWater.com
Save up to 50%

Contact Us

Live Hours
7:00a-4:00p p.s.t.
Monday-Friday

Toll Free
800-460-9011

local/International
818-786-0600

Fax
818-786-2347

E-MAIL US

ResinDepot

Lab Water Specials

Featured Products
HUGE SAVINGS!

APSULTRA Brand
Replacement Filters
For
Millipore Lab Water Systems

Milli-Q
Academic
Biocel
Synthesis
Gradient
Element
Gradient
Simplicity
AFS Systems

Filters for ALL Millipore Water Systems

11/20/2009
5:09:28 PM

Tags : how | change | filters | in | barnstead | e-pure | | nanopure | nanopure | ii | water | systemalthough | proceedure | specifically | for | barnstead | epure | water | systems |
How to change filters in Barnstead E-Pure , Nanopure and Nanopure II Water System

Terms and conditions
Privacy Policy

* UPS shipping included where able to ship items via UPS Standard Freight in the continental USA. Over Size freight may have additional charges. All will be notified if freight charges apply. Most items can be shipped UPS. If a return is made, you are responsible for our actual UPS shipping charges. That amount is not refundable.

**We are normally only required to collect sales tax in California. For this discount program, we are paying this tax on your behalf out of the proceeds of the total sales. This is equal to a 9.25% discount for California clients. Sales from other states are not subject to our witholding but taxable by your state. In this program we are only paying the tax on sales we are required to collect which at this time is California only. This discount may not be used in combination with other discount offers except for the free freight offer.

All freight charges quoted on this web site are for continental USA only. Freight is calculated based on a starting point of Van Nuys, California. 91406 shipping from a business location to a business location. If we ship your order out of warehouses located in other locations or if you are in a rural or residential location, your freight charges may differ significantly. You will be notified if the freight charges on your order differ.

Images are representative of the product and not necessarily the actual image of the product.

*To the extent that APS WATER uses trademarks, servicemarks, tradenames, or other identifying information of other companies, APS WATER is making use of those Trademarks for identification, or is making use by permission. The owner of the trademarks has not consented to further use or copying of the trademarks and APS WATER can not license such trademarks. Millipore , Q-Pak , Super-Q , Super-C , Milli-Q , ROGARD , Milli-RO , ROPAK , AFSPAK , Polygard, Gradient, Synthesis, AFS, SDS, Acadenic, Biocel, Element, progard, ggard, quantum, Millipak and any tradenames prefixed by the words Millipore or Millipore's are trademarks of Millipore Corporation. Barnstead, Nanopure , E-pure , B-pure , Nanopure Diamond,Infinity , Easypure , ROPURE , Bantam and Mega-pure are trademarks of Barnstead/Thermolyne. Labconco and Waterpro are trademarks of Labconco inc. Continental, IWT, US Filter, Modulab and Culligan and other water related trademarks are trademarks of their respective owners.

This is not necessarily a full list of the trademark notifications we must make, If you see one we inadvertently left off,

please contact 800-460-9011 to have it added.

(C) 2001-2009 APS Water Services Inc. All Rights Reserved.
APS ULTRA brand water purification products are designed to be replacement filters and membranes for Millipore , Barnstead , and US Filter water purification systems.

Scott Wilson Memorial
Gleva Wilson Memorial
Lab-Directory.com