Troubleshooting A Water Pressure Bladder Tank
For Expert Technical and Customer service call us at 800-460-9011 : Need Quick Help? Try Ask Amy
Products For Industry and Homes
Laboratory Equipment Laboratory Filtration Lab Water FIltration
Fume Hoods Glassware Washers Home Water FIltration
APS Scientific
High Quality Laboratory Products
laboratory equipment Laboratory Equipment
Laboratory Water Products Laboratory Water
Laboratory Filters Laboratory Filters
Residential Water Products Commercial / Residential Water

APS TechNotes See all articles

Troubleshooting A Water Pressure Bladder Tank

Quick check for blown bladder

1. Turn off pump
2. Open faucet (wait for flow to stop, leave open)
3. Shake bladder tank
4. If it still has water in it, it is blown

What is a bladder pressure tank?

It is a type of tank containing pressurized air and water separated by a membrane (bladder). They are precharged with air at the factory. An average bladder pressure tank lasts 5-7 years.

Also See :

  • Different uses for Water Pressure Bladders

  • Pressure Bladders can be found here

    How do bladder pressure tanks work?

    As water pressure changes, the volume of air in a bladder pressure tank contracts and expands. Periodically, the amount of air in the tank should be measured and the tank recharged if the air is too low. Bladder pressure tanks do not provide any useful water storage capacity.

    What functions do bladder pressure tanks serve?

    Maintain a desired range of water pressure in the distribution system.

    Minimize pump cycling, preventing frequent starts and stops protecting facilities from damage.

    Protect against water hammer.

    Troubleshooting Guide - Check the bladder pressure tank air charge

    Disconnect electrical power to the pump.

    Drain the tank by opening the closest faucet.

    Check tank pressure by placing a tire gauge on the air-charging valve on top of the tank.

    Add air if the pressure is more than 2 psi below the
    pump cut-in pressure (lowest pressure in the range). Use a tire pump or air compressor. Use caution with an air compressor.

    Release air if the pressure is 2 psi above the pump cut-in pressure.

    Check for leaks in the air charging system. Use a soap solution to check the air charging valve for leaks.

    Re-start the pump and run through a normal cycle to verify the setting.

    Helpful hint! If tank pressure drops, the bladder may have a tear or hole in it.

    Check for waterlogged bladder pressure tank problems

    A tank is waterlogged if it is completely filled with water or has too much water to function correctly.

    Waterlogged bladder pressure tanks contribute to the following problems :

    The pump motor cycles turns on and off too often.

    Frequent cycling can shorten the lifespan of a pump. 1 to 5 HP pump motors should not cycle more than five times an hour. If your pump is cycling, check to see if the tank(s) is waterlogged.

    Unsatisfactory coliform samples or taste and odor complaints. Waterlogged tanks contain stagnant water that can contribute to bacterial problems or taste and odor complaints.

    Premature tank failure. The inside walls of a waterlogged tank can corrode and weaken from the exposure to water.

    Helpful hint! It is often most cost-efficient to replace a waterlogged tank.

    Drinking Water Tech Tips :

    If your tank is waterlogged, check for possible causes
    Bladder pressure tanks can become waterlogged for many
    reasons. Some of the more commons reasons are:

    Sediment, such as iron and manganese, can coat
    the surface of a bladder, causing it to harden and
    become less flexible.

    Sediments can plug the fill or draw line, preventing
    the tank from filling and emptying normally.

    High levels of chlorine can damage the bladder,
    causing it to become brittle and less flexible.

    Tanks sitting directly on the ground rust and lose
    structural integrity.

    Chlorinators give off corrosive vapors that cause
    the tank to rust.

    Remember! When working with bladder pressure tanks
    it is important to read and follow the Manufacturers Safety Warnings!

  • Got Millipore?
    Click Here
    For Huge Savings

    We Offer Over 28,000 Products
    Troubleshooting A Water Pressure Bladder Tank
    Purchase Orders Accepted
    (subject to approval)
    Credit Application

    Rated "A+" with the BBB
    27 years
    Zero Complaints

    Best ...

    Need Help?

    Dialysis Product
    Myron L D-1 Dialysate Meter

    Myron L D-1
    Dialysate Meter
    Great for all Dialysis Centers

    Best New Product
    Quick Twist Reverse Osmosis System

    Quick Twist
    Reverse Osmosis System
    Great for Lab Water Pretreatment
    or Great Drinking Water

    Got Well Water?
    Sentry Complete Well Water Treatment System Sentry
    Complete Treatment System
    Own your own Municipal
    Water Treatment Plant

    New Features
    Lab Water Filter Database

    Millipore Filter Quick List
    Barnstead Filter Quick List

    Filters for your Lab Water System?
    Lab Water Systems Database

    Barnstead Micropure - Troubleshooting A Water Pressure Bladder Tank
    No Description... ... Are You Lost?
    See Your Breadcrumbs
    List All Products

    APS Water Services Corp. 7320 Valjean Ave, Van Nuys, CA. 91406
    800-460-9011 Toll Free | 818-786-0600 Local/International | 818-786-2347 Fax |

    Best Best Best Carbon Filter

    Images may or may not be of actual product.

    * Flat Rate UPS shipping when able to ship via UPS and is in the USA excluding Hawaii and Alaska.
    Larger Items may not be able to ship via UPS, in that case freight charges will be quoted seperately.

    3/19/2018 at 2:58:41 PM
    Tech Articles

    Terms and conditions
    Credit Application

    Privacy Policy

    Tags :

    Troubleshooting A Water Pressure Bladder Tank
    Clack is a registered trademark of Clack corporation